If you’re running a packaging line—whether it’s for soda, pharmaceuticals, personal care, or even household chemicals—you know how much rides on a simple bottle cap. For injection molded cap suppliers like us, a single tiny defect can throw off an entire production run, cost our clients thousands in downtime, and even hurt their brand reputation. Over 10 years in this game, I’ve seen every kind of cap defect imaginable, and the good news is most of them are preventable if you know what to look for. Let’s break down the most common ones, why they happen, and how we fix them at our shop. Plastic Injection Cap Molding

First up: flash. That’s that thin, sliver-like excess plastic that sticks to the edges of a cap, usually around the threads or the top seal. Think of it like a tiny wrinkle between two pieces of a mold. At first, I thought flash was just a weird quirk of cheap machinery—turns out, it’s way more nuanced. When we inject molten plastic into the mold cavity, if the injection pressure is set too high, or the mold halves aren’t clamped tight enough (even a tiny gap of a few thousandths of an inch will do it), the plastic squeezes out. Material can also be a factor: thicker, more fluid plastics (like LDPE or PP used for many food-grade caps) are more prone to seeping through gaps. I once had a client who blamed our shop for flash on their 2-liter soda caps, only to realize their mold’s clamping unit had worn down 10% over a year of heavy use—easy fix, just a mold part replacement. Another time, we had flash on a batch of child-resistant medication caps because the resin moisture content was too high; wet plastic melts faster, so it seeped through gaps way easier. Flash might seem harmless, but that sliver can break off inside a bottle, contaminate the product, or make the cap impossible to screw on evenly. We fix it by calibrating clamping pressure to match each mold, drying resins to their exact specs, and doing a 10-minute mold check before every production run to spot any small gaps.
Next, short shots. That’s when the mold cavity doesn’t get filled all the way, leaving a cap that’s missing parts of the thread, the seal, or even the top lip. A common mistake here is assuming “if it’s close, it’s fine”—but a short shot thread means a cap will cross-thread on a bottle, or pop off mid-transit. Why does this happen? Under-injection pressure is the big one, but so is cold plastic. If the melt temperature is too low, the plastic gets too thick to flow all the way into every nook of the mold, especially for complex caps with tiny features (like tamper-evident rings with small notches). We had a client’s protein supplement caps come back with short tamper rings last year, and it turned out their resin was stored in a cold warehouse overnight—when we ran a test, the melt temp was 15°F lower than our standard, so the plastic didn’t reach the far edges of the mold. Another cause: clogged nozzles or cold runners in the injection machine. If there’s old plastic stuck in the nozzle, it acts like a plug, so the new plastic can’t flow through. Short shots are easy to spot at first glance, but sometimes they’re subtle—we do a 100% visual inspection for all critical caps, and a random sample test for every batch to catch even tiny gaps.
Then there’s sink marks. Those are those dimples or indentations on the inner or outer surface of the cap, usually on thick parts like the top wall where the tamper ring connects. Sink marks happen because plastic shrinks as it cools—thicker sections take longer to cool, so the outer layer hardens first, and the inner part pulls inward, creating a dimple. At worst, a sink mark on the inner seal can break the airtight seal of a jar of pickles, letting air in and ruining the product. Why? Too much mold cooling time, or not enough packing pressure. If you inject plastic and don’t hold enough pressure while it sets, the inner material can’t fill the space left by shrinkage. We fix this by adjusting packing pressure (we hold pressure for 2-3 seconds for most caps, depending on thickness), and adding tiny “ribs” to thick cap sections to reduce the amount of material that needs to shrink. I’ve seen clients try to sand down sink marks on finished caps—total waste of time, because that ruins the material’s structure and can create leaks. Sink marks are a big one for food and beverage clients, where hermetic seals are non-negotiable.
Thread defects are another nightmare—these are problems with the screw threads that make it impossible to get a tight seal. Common thread issues: stripped threads, cross-threading, or threads that are too loose or too tight. Loose threads happen when the mold cavity is oversized, so the cap’s internal threads are too big for the bottle’s external threads. Tight threads are the opposite—mold is too small, so the cap won’t screw on without forcing it, which can crack the tamper-evident ring. Cross-threading usually happens if the cap’s threads are offset, so they don’t align with the bottle’s threads, but that’s almost always a mold alignment issue, not an end-user error. We had a craft brewery client last year who was getting 5% of their caps cross-threading, and after checking the mold, we found the mold’s thread inserts had worn down 0.002 inches, which was enough to throw alignment off. Thread defects might not sound like a big deal, but in a packaging line, that’s 5% of your production running slowly, and for a brewery, that’s hundreds of cases lost every hour. We solve this by doing regular thread gauge tests on every mold—we use calibrated screw gauges to check that internal cap threads match the exact spec for the client’s bottles, and we replace worn inserts every 500,000 shots to keep accuracy.
Tamper-evident ring defects are specific to caps that need that safety seal—you know, the ring that stays on the bottle when you twist the cap off. Defects here range from rings that break too easily when twisting, to rings that stick to the cap and stay on the bottle, or even rings that are missing entirely. A missing tamper ring is a big red flag for regulators and consumers—pharmaceutical or food products can’t sell without a proper tamper seal, so a batch like that is a total loss. Why do rings break too easily? Thin ring walls, or not enough melt flow to fill the ring’s tiny notches. If the injection pressure is too low, the plastic won’t fill the small grooves that connect the ring to the cap, so it snaps off too early. If the ring is too thick, it sticks to the bottle, which is a problem for clients who want their consumers to hear that “pop” sound when the ring releases. We had a baby formula client who complained their tamper rings were sticking, so we adjusted the ring’s wall thickness by 0.001 inches and added a tiny release agent to the mold’s ring area—fixed the issue immediately. Missing rings, of course, come from short shots—if the mold’s ring cavity doesn’t fill, the ring doesn’t exist. We run a visual inspection that checks every cap’s tamper ring, and we use a ring tension test for all pharma caps to make sure it’s just strong enough to stay on during transit, but weak enough to break when the first twist happens.
Another less talked-about defect: dimensional inaccuracy. That’s when the cap’s height, diameter, or seal width doesn’t match the client’s spec. It might seem small, but a cap that’s 0.005 inches too tall won’t fit on the capping machine, or a seal that’s too narrow won’t create an airtight seal. This happens when the mold’s temperature fluctuates too much—plastic expands when it’s hot, contracts when it’s cold, so if the mold isn’t kept at a steady temperature, the final cap size changes. We had a coffee roaster client last year who was getting caps that were 0.01 inches too narrow, so their capper was misaligning them. Turned out their shop was running 3 different cap molds on the same machine, and the mold’s cooling system was set too low for the coffee cap, causing shrinkage. We adjusted the mold temperature to 100°F (38°C) specifically for their caps, and the dimensional issues went away. We also do sample measurements every 2000 shots, using digital calipers, to catch any dimensional shifts before a whole batch goes bad.
What about cosmetic defects? Even if a cap works perfectly, if it has surface scratches, bubbles, or discoloration, your client will reject it. Bubbles come from trapped air in the mold, or moisture in the resin—like we talked about earlier, wet plastic melts create steam bubbles when injected. Scratches usually happen during demolding, when the cap is pushed out of the mold too roughly, or when it’s handled improperly after molding. Discoloration is either from old resin (recycled plastic that’s been melted too many times) or from burnt plastic in the injection nozzle. We fix bubbles by drying resins to 0.02% moisture content, venting the mold to let air escape during injection, and making sure the nozzle is clean. For scratches, we use soft demolding pins and add a protective plastic layer during transport from our molding machine to our inspection area. For discoloration, we run daily checks on our melt temperatures to make sure we don’t burn resin, and we use virgin or food-grade resin for all our client batches (we only use recycled resin if a client specifically requests it, and then we make sure it’s properly filtered).
Wait, let’s be clear—none of these defects are unavoidable, at least not at a professional shop that’s serious about quality. I see so many new cap molding providers cut corners: skimping on mold maintenance, not calibrating machines, using low-quality resin. But when a cap client is dealing with production downtime, product waste, and brand damage, cutting corners just isn’t worth it. At our shop, we track every defect per batch, and we keep a log of every mold’s maintenance schedule, so if a client has a repeat issue, we can go back to the log and see exactly what happened. For example, last quarter, we had a batch of shampoo caps with sink marks, and when we checked the log, we saw the cooling water had been turned off for 20 minutes during a shift change. We adjusted our shift checklists to include a cooling water check every hour, and that problem hasn’t popped up since.
If you’re a packaging manager, a brand owner, or someone who’s tired of dealing with bad caps that mess up your line, here’s the thing: the right injection molding supplier doesn’t just give you a quote—they partner with you to fix defects before they happen. We’ll send you samples before every batch, run small test runs, and work with you to adjust specs if you’re having issues with your bottles or capping machines. We don’t sell one-size-fits-all caps—every mold is calibrated to your exact bottle size, your product’s needs, and your production line’s requirements.

If you’ve been dealing with flash, short shots, sink marks, or any other cap defects that are costing you time and money, reach out to our team to discuss your needs. We’ll help you figure out what’s going wrong, and work with you to get consistent, high-quality caps that keep your products safe and your line running smoothly. Let’s make your packaging process easier, one cap at a time.
Plastic Medical Supplies References
- Engineering Plastics for Packaging, Society of Plastics Engineers, 2022
- Injection Molding Defect Analysis Guide, American Injection Molding Council, 2021
- Food and Drug Administration Guidance on Plastic Packaging Materials, 2020
- Plastic Cap Manufacturing Best Practices, Packaging Machinery Manufacturers Institute, 2023
Taizhou Huangyan MinCong Mould and Plastic Co., Ltd.
Taizhou Huangyan MinCong Mould and Plastic Co., Ltd. is well-known as one of the leading plastic injection cap molding manufacturers and suppliers in China. If you’re going to buy high quality plastic injection cap molding at competitive price, welcome to get pricelist and quotation from our factory. Also, customized service is available.
Address: No.158 Huang Zhou Road, Western industry, Huang Yan District, Taizhou City, Zhejiang Province
E-mail: Mouldsupplier6@gmail.com
WebSite: https://www.capmoldsupplier.com/