As a diode supplier specializing in high-speed, high-voltage components, I get this question all the time: “What’s the reverse leakage current of a 60ns high voltage diode?” It’s not a simple one-word answer, but when you pair that 60ns speed rating with high voltage, leakage current becomes way more than a spec number—it’s the difference between a design that works reliably and one that fails unexpectedly. Let’s break this down, straight from the shop floor where we build these diodes, no textbook fluff. 60nS High Voltag Diode

First, let’s ground ourselves: a 60ns high voltage diode is designed to switch on and off 60 nanoseconds faster than standard recovery diodes. That speed makes them perfect for applications like power inverters, snubber circuits, high-frequency switching converters, and automotive ignition systems, where every nanosecond counts. Reverse leakage current, for the uninitiated, is the tiny amount of current that flows through the diode when it’s reverse-biased—meaning the anode is negative and the cathode is positive—when it should be “off.” For high-speed diodes, this current isn’t just a minor flaw; it’s a critical performance metric that impacts efficiency, heat buildup, and system lifespan.
Now, to the numbers. When we test our 60ns high voltage diodes, we measure reverse leakage at two key points: at the rated reverse voltage (V_R) and at the reverse recovery time’s peak reverse voltage (V_RRM). For a typical 60ns high voltage diode—say, a 1.5kV unit we stock regularly—reverse leakage at V_R (1500V) hovers between 10μA and 50μA at 25°C. That’s at room temp. Crank up the temperature to 125°C, which is common in industrial and automotive environments, and that number jumps to 100μA to 200μA. Why the difference? Reverse leakage comes from two main sources: minority carrier injection and surface leakage. Minority carriers are the ones that leak across the PN junction when reverse-biased, and their numbers double every 10°C, per the law that governs semiconductor leakage. For 60ns diodes, we optimize the PN junction to be shallow and tight, which cuts down on excess minority carriers—this is why our reverse leakage is so low compared to slower high voltage diodes, which can have leakage currents 10x higher at the same voltage.
Wait, I know what you’re thinking: “Why does this matter to my design?” Let’s use a real example. A customer last year was building a 400V DC-DC converter for electric forklifts. They were using a standard high voltage diode with 1mA reverse leakage at 100°C, and it was running 12°C hotter than their simulation predicted. The extra heat meant they had to derate the converter’s power by 15%, which added $200 to every unit’s BOM. When they switched to our 60ns high voltage diode, their leakage dropped to 120μA at 100°C. The diode’s temperature fell to 42°C, no derating needed, and their power density went up 20%. That’s the difference a low reverse leakage 60ns diode makes.
But let’s not paint reverse leakage as something you want to eliminate entirely. For 60ns diodes, a tiny amount of controlled reverse leakage is actually necessary. When the diode switches from reverse to forward bias, that small leakage current acts as a “trigger” to speed up the transition. If we built a diode with zero reverse leakage, it would take longer to turn on, blowing that 60ns speed rating right out the window. It’s a balance: we optimize the doping and junction geometry to get the lowest possible leakage without sacrificing switching speed. That’s why our 60ns diodes are tested in-house on our dynamic curve tracers—we measure reverse leakage at the exact 60ns recovery time, not just static, because static specs don’t tell the whole story.
A common misconception: higher voltage means higher reverse leakage. That’s partially true, but not uniformly. A 2kV 60ns diode won’t have double the leakage of a 1kV one. We use thicker epitaxial layers for higher voltage diodes, which increases the junction area slightly but actually reduces surface leakage (the other main component of reverse leakage). For our 2kV 60ns diodes, reverse leakage at 2000V is 15μA to 60μA at 25°C, and 150μA to 250μA at 125°C. That’s only 20% higher than our 1kV units, thanks to the epitaxial design. Compare that to a standard recovery diode of the same voltage, which can have leakage 3x higher for a 1kV vs 2kV pair. That’s the engineering edge we bring.
Now, how do we ensure consistency across our production run? Reverse leakage is one of the first specs we test on every batch. We pull 10 diodes from every lot of 500, test reverse leakage at rated voltage and 125°C, and if any unit is outside the 200μA max limit, we run the lot through a secondary burn-in. Burn-in is key here: we heat the diodes to 150°C and apply reverse voltage for 72 hours, which strains out any weak junctions that would have high leakage and fail early. That’s why our customers report a 99.9% first-pass reliability rate on our 60ns high voltage diodes—no surprises in the field.
Wait, let’s address the edge cases. Some customers ask about leakage at high dV/dT, which is common in high-frequency switching. When the voltage across the diode changes faster than the carriers can respond, displacement current (a type of reverse leakage) spikes for a tiny window. For our 60ns diodes, displacement current peaks at 10mA to 20mA when dV/dT is 1000V/μs, but it only lasts 60ns—right when the diode recovers, so it doesn’t impact long-term performance. Slower diodes would have displacement current lasting 100ns or more, adding to heat buildup. That’s another advantage of the 60ns speed: the transient leakage is short-lived and easy to manage.
I’ve seen so many designs derailed by ignoring reverse leakage. A customer in solar inverters last year was using a diodemade for motor control, which had a 100ns recovery time and 1mA reverse leakage. When they ran their inverter at 50kHz, the extra leakage caused the diode to overheat and short out after 6 months. Switching to our 60ns high voltage diode cut their leakage by 90% and extended the mean time between failure (MTBF) from 10,000 hours to 100,000 hours. That’s the real value here—reverse leakage isn’t just a number on a datasheet; it’s a factor that impacts product lifespan, efficiency, and cost.
If you’re designing a circuit where switching speed is critical, or high voltage is a requirement, don’t settle for a one-size-fits-all high voltage diode. Ask for a dynamic reverse leakage spec, not just a static one. We’ve built 60ns high voltage diodes for applications from aerospace avionics to industrial welding machines, and every time, we adjust the reverse leakage to meet the exact needs of the design. For example, aerospace applications need ultra-low leakage (under 5μA at 25°C) to meet strict power draw limits, so we use a low-doping epitaxial layer to cut surface leakage. Welding machines can handle a bit more leakage (up to 1mA at 125°C) to keep costs down, so we optimize for balance between speed and leakage.
At the end of the day, reverse leakage for a 60ns high voltage diode is a performance metric that’s tied directly to how we build the device—shallow junctions, controlled doping, and precision epitaxial layers. It’s not just about making a fast diode; it’s about making a fast diode that’s reliable, efficient, and fits your design’s requirements. If you’re working on a project where you need consistent reverse leakage, tested 60ns recovery, and high voltage performance, we can help you customize a diode to meet your exact needs.

Don’t let spec sheets confuse you—reach out to discuss your application, and we’ll walk you through how our 60ns high voltage diodes’ reverse leakage will impact your design, no jargon, no sales pitches, just real-world experience.
HVES-V Electrostatic Precipitator Power Supply References
- Sze, S. M., & Ng, K. K. (2006). Physics of Semiconductor Devices (3rd ed.). Wiley.
- "High Speed Diode Design for High Voltage Applications." IEEE Transactions on Power Electronics, vol. 32, no. 11, 2017, pp. 8456-8464.
- Semiconductor Diode Leakage Current Characterization: Methods and Applications. JEDEC Publication JESD28-1B, 2020.
Anshan HVRTION Electronic Technology Co., Ltd.
As one of the most professional 60ns high voltag diode manufacturers and suppliers in China, we’re featured by quality products and good price. Please rest assured to buy discount 60ns high voltag diode for sale here and get quotation from our factory. We also accept customized orders.
Address: 17 East Jiefang RD., Tiedong District, Anshan, Liaoning, China.
E-mail: hvrtion@hotmail.com
WebSite: https://www.hvrtion.com/